Outils pratiques pour un travail de précision
Calculateur d'Angle d'Onglet
Trouvez l'angle de scie à onglet pour un cadre à forme régulière ou un angle de coin personnalisé.
Sides: whole number ≥ 3. Angle: degrees.
Set your miter saw to the miter angle shown, and cut that same angle on both pieces meeting at the corner.
How it works
How to use it: for a regular shape (a frame, planter or table with equal sides - like a square, hexagon or octagon), choose Regular shape and enter the number of sides. For an irregular corner - an out-of-square wall, an odd-shaped frame - choose Custom corner angle and enter the actual angle between the two pieces.
Formula. Every two-piece corner has an interior corner angle. The miter angle - the number you set on the saw, measured from a square (0°) cut - is half of what's left after the corner angle: miter angle = (180° − corner angle) / 2. For a regular polygon of n equal sides, the corner angle is (n − 2) × 180° / n, so the two modes agree: a 4-sided frame has a 90° corner and a 45° miter; a hexagon has a 120° corner and a 30° miter.
Worked example. With the default (regular shape, 4 sides): corner angle = (4−2) × 180 / 4 = 90°; miter angle = (180 − 90) / 2 = 45° - the familiar 45° setting for a square picture frame. For an 8-sided shape: corner angle = (8−2) × 180 / 8 = 135°; miter angle = (180 − 135) / 2 = 22.5°.
Current-input example
The result above uses these exact values. This snapshot is included when the page is printed so the output can be checked against the original measurements.
- Corner type
- Regular shape (equal sides)
- Number of sides, or corner angle
- 4
Primary result: Miter angle: 45.00 deg.
Before using the result
- Measure from the datum or reference edge described by this tool, and do not mix inside, outside and centerline dimensions.
- Keep inputs in the displayed units and preserve more precision than the final cutting or purchasing tolerance requires.
- When the result is close to a limit, verify it with a test piece, field measurement, manufacturer drawing or qualified project professional.
Limitations
This calculates the miter angle for a flat, single-bevel corner joint only - it does not compute compound miter/bevel pairs for angled (non-vertical) material such as crown moulding run at a spring angle, which needs a second, tilt-plane angle as well.
"Regular shape" mode assumes every side is the same length and every corner is identical, which is true for a regular polygon but not for an arbitrary irregular frame - measure each corner separately with the custom-angle mode if your shape isn't regular.
Frequently asked questions
Why does a square frame need a 45° miter, not a 90° cut?
The 90° is the corner angle the two boards form once joined - each board only needs to turn half of that (45°) so the two 45° cuts add up to the full 90° corner.
What if my wall or frame corner isn't a standard shape?
Measure the actual angle between the two surfaces with a protractor or angle finder, then use Custom corner angle mode with that measurement instead of guessing a side count.
Does this account for saw blade kerf or material thickness?
No - it returns the geometric angle only. Kerf and thickness affect the piece lengths you cut to, not the angle, and depend on your specific saw and material.
Outils associés
Calculateur Pied-Planche
Calculez les pieds-planches et le coût total du bois de dimension.
Calculateur Découpe Contreplaqué
Imbriquez une liste de pièces quelconques sur des panneaux pour minimiser les chutes, avec un plan de découpe visuel imprimable.
Optimiseur Débit Linéaire
Optimisez la découpe d'une liste de longueurs à partir de barres/planches en stock, en minimisant les chutes et le stock utilisé.
Calculateur Caisson de Tiroir
Dimensionnez un caisson de tiroir à partir de l'ouverture du meuble et de la longueur de coulisse, puis envoyez les pièces vers un optimiseur de découpe.